Downloads
- Easy installation and removal
- Several gas types, freely adjustable
- Diameter freely adjustable
- Easy installation and removal under Pressure thanks to 1/2″ Ball valve
- Several Gas types – freely adjustable on the DS 400
- Can be used from 1/2″ to 12″ DN 300
- Diameter freely adjustable on the DS 400
- 4…20 mA output for m³/h
- Pulse output for m³ (Total consumption)
- 3.5″ graphic display with touchscreen shows the measured value curve graphically
- 2 sensor inputs for consumption or Dew point sensors
- USB interface for reading out the Data loggers via USB stick
- “Option” 2 additional sensor inputs for pressure sensors, electricity meters, etc.
- “Option” Data logger for 100 million Measured values (2 GB SD card)
- “Option” Ethernet and RS 485 interface (Modbus protocol)
- “Option” Web server
- “Option” CS Soft Basic – convenient evaluation of measurement data
Features:
Each factory needs compressed air, however, often it is not realized that compressed air is one of the most expensive types of energy. Therefore, the intelligent use of flow measurement DS 400, holds an enormous potential for saving energy. In most cases the user mainly concentrates on the production, i. e. on the compressors. In order to save energy very often new compressors, control systems or heat recovery systems are installed.
- Easy installation and removal under pressure via 1/2″ ball valve
- Several gas types – freely adjustable at DS 400
- Usable from 1/2″ to 12″ DN 300
- Diameter freely adjustable at DS 400
- Output for 4…20 mA for m³/h
- Pulse output for m³ (total flow)
- 3.5″ graphic display with touch screen – shows the progression of the measured values in graphic form
- 2 sensor inputs for flow sensors/ dew point sensors
- USB interface for reading out the data logger via USB stick
- 2 additional sensor inputs for pressure sensors, current meters and so on
- Option: Data logger for 100 million measured values (2 GB SD card)
- Option: Ethernet and RS 485 interface (Modbus protocol)
- Option: Webserver
- Option: CS Soft Basic – comfortable evaluation of the measured data
Specs
Contact Us Today To Enquire About Our Products And Services
Product Specification
Below is the product specification of the DS400 Multi-Functional Flow Station for Compressed Gases from CS Instruments. If you require further information, please contact our expert customer service advisors on 01722 442 307.
Technical data VA 500:
Parameters:
m3/h, I/min (1000 mbar, 20°c) in case of compressed air resp. Nm3/h, NI/min (1013 mbar, 0°C) in case of gases
Units adjust able via keys at display:
m3/h, m3/min, I/min, I/s, ft/min, cfm, mis, kg/h, kg/min
Adjustable via keypad:
diameter for volume flow calculation, counter resettable
Meas. principle:
calorimetric measurement
Gas types adjustable via external device DS 400, DS 500, PISOO:
air, nitrogen, argon, nitrous oxide, CO2, oxygen
Accuracy (m.v.: of meas. value) (f.s.: of full scale):
± 1.5 % of m.v. ± 0.3 % of f.s. on request
± 1.0 % of m.v. ± 0.3 % of f.s.
Operating temp.:
-30 … 110 °C probe tube
-30 … 80 °C housing
Operating pressure:
up to 50 bar
Digital output:
RS 458 interface, Modbus RTU, M-Bus (optionally)
Analogue output:
4 … 20 mA for m3/h resp.I/min; on request:
scaling for cfm,m3/min, I/min, I/s, ft/min, mis
Pulse output:
1 pulse per m3 resp. per liter galvanically separated
Power supply:
18 … 36 voe, 5 w
Burden:
< 500 ΩHousing:
polycarbonate
Probe tube:
stainless steel, 1.4301
mounting length 220 mm,
010mm
Mountain thread:
G 1/2″
Technical data DS 400:
Dimensions:
118x 115 x98mm
IP 54 (wall housing)
92 x 92 x 75 mm
(panel mounting)
Inputs:
2 digital inputs for VA 500/520
Interface:
USB
Power supply:
100 … 240 VAC, 50-60 Hz
Accuracy:
please see VA 500
Alarm outputs:
2 relays, (pot.-free)
Options:
Data logger:
100 million measuring values start/stop time, measuring rate freely adjustable
2 additional sensor inputs:
f or connection of pressure sensors, temperature sen sors, clamp-on ammeters, third-party sensors with 4 … 20 mA Oto 10 V, Pt 100, Pt 1000


